NEBLI
DJI live streaming

Live streaming a DJI Matrice 300 RTK

Yes. A Matrice 300 RTK on the DJI Smart Controller Enterprise streams live from DJI Pilot 2, using Pilot 2's custom live stream setting with an RTMP address, per DJI's Matrice 300 RTK manual. The stream leaves from the remote over the remote's internet connection, so the aircraft needs no connection of its own. We have not streamed a Matrice 300 RTK on our own bench; the model details below are per DJI's documentation.

01

Register the drone in Nebli

Add a DJI drone in the Nebli dashboard. It shows one RTMP URL that ends in a short pairing code.

02

Paste the one Pilot 2 URL

In Pilot 2's custom live stream setting, paste the whole URL into its single RTMP URL field. To change an active stream, exit it first. The Pilot 2 guide shows each screen.

03

Share the PIN page

Start the stream. The drone's page goes live in a browser; share the link and its PIN. Video only, nothing to install.

The Nebli viewer page playing a drone's live feed in a browser, with a LIVE badge over the picture
The page your viewers open: the live picture in a browser, behind a PIN. Screenshot from our bench.

What a Matrice 300 RTK stream carries

Per DJI's documentation, except where a line says we measured it.

Matrice 300 RTK
CamerasWhatever payload you fit. DJI lists the Zenmuse H20, H20T and H20N among them, and the H30 series with the DJI RC Plus; the H20T, H20N and H30T carry thermal cameras
QualityDJI's developer documentation lists five levels for a stream a platform starts, up to 1080p at 3 Mbps. DJI does not list the levels in Pilot 2's own live stream menu
Mobile dataAbout 4 to 6 GB an hour, measured on our Matrice 4E, not this model
SoundNot stated by DJI

Two remotes, one app

Per DJI, the Matrice 300 RTK works with the DJI Smart Controller Enterprise and, after a firmware update to the remote, the DJI RC Plus. DJI lists the Matrice 300 RTK with Pilot 2 on both, but its Matrice 300 RTK manual, where the custom RTMP stream is described, covers the Smart Controller Enterprise. Either way the stream leaves from the remote, not the aircraft. Per DJI, the Smart Controller Enterprise takes a 4G dongle and its built-in battery runs about 2.5 hours; the RC Plus has Wi-Fi 6. The aircraft's maximum flight time is 55 minutes.

If you are choosing a newer aircraft, the Matrice 350 RTK uses the RC Plus only.

When the stream will not start

The remote still runs DJI Pilot. The steps here are for DJI Pilot 2. DJI's current Matrice 300 RTK manual is its DJI Pilot 2 edition; the older DJI Pilot edition will not be updated, per DJI.

You cannot edit the address. If a stream is already set up, Pilot 2 opens a summary instead of the editor. Tap Exit, confirm, then edit.

Part of the address is missing. The whole URL goes in the one RTMP URL field, with the pairing code at its end.

The remote has no internet. The stream leaves from the remote, so check its connection before you check the drone.

Put your next flight on a page your client opens in a browser.

Common questions

Can a DJI Matrice 300 RTK live stream?

Yes, from DJI Pilot 2 on the DJI Smart Controller Enterprise to a custom RTMP address, per DJI's Matrice 300 RTK user manual (v4.0, the Pilot 2 edition).

Which remote does a Matrice 300 RTK stream from?

Per DJI, the DJI Smart Controller Enterprise or the DJI RC Plus, both with DJI Pilot 2. The RC Plus needs a firmware update first.

How much mobile data does a Matrice 300 RTK live stream use?

Plan for about 4 to 6 GB an hour, measured on our Matrice 4E, not this model. Ours ran at roughly 9.5 to 14 Mbps while Pilot 2's label read 1.5 Mbps.

Which Matrice 300 RTK payloads have a thermal camera?

Per DJI, the Zenmuse H20T and H20N, and the Zenmuse H30T when the aircraft flies with the DJI RC Plus.